The new RD30F HydraFlex™ Draper offers a 30-foot width that allows you to stretch your productivity to new heights, particularly in rice or soybeans.
- Harvest crops as close as possible to the ground with the HydraFlex™ cutterbar
- Minimize grain loss with a two-speed center feed section
- Enable higher harvesting speed without sacrificing cut quality with a 4” double cut, dual drive, shaft driven cutterbar
- Get more done by eliminating header calibrations
Call Us
- Anna, Ohio937-693-2221
- Franklin, Indiana317-738-2250
- Greenfield, Indiana317-462-5585
- Greensburg, Indiana812-663-5992
- Greenville, Ohio937-548-1151
- Oxford, Ohio513-523-4169
- Richmond, Indiana765-962-7330
- Rushville, Indiana765-932-2977
- Urbana, Ohio937-653-5281
Manufacturer
John Deere
Category
Draper Platforms
Location
Anna, Ohio
Franklin, Indiana
Greenfield, Indiana
Greensburg, Indiana
Greenville, Ohio
Oxford, Ohio
Richmond, Indiana
Rushville, Indiana
Urbana, Ohio
Specs
| Key Specs: | |
|---|---|
| Cutterbar length | 9.14 m 30 ft |
| Knife drive | Double-cut, dual-drive, shaft-driven cutterbar: 10.2 cm 4 in. |
| Knife speed | X Series Combine: 520 cycles/min S-Series Combine: 490 cycles/min |
| Pickup reel operating speeds | 6-70 rpm |
| Draper belts speed control | Hydraulic from cab (side belts only) |
| Platform: | |
| Type | Rigid frame flexible cutterbar |
| Cutterbar: | |
| Type | Straight-line knife drive system Cutterbar vertical flex: 190 mm 7.5 in. |
| Length | 9.14 m 30 ft |
| Knife drive | Double-cut, dual-drive, shaft-driven cutterbar: 10.2 cm 4 in. |
| Knife speed | X Series Combine: 520 cycles/min S-Series Combine: 490 cycles/min |
| Cutterbar tilt | |
| Base skid shoe height | 3.8 cm 1.5 in. |
| Pickup reel: | |
| General | One-piece, poly tine pickup reel with 10-in. (25-cm) tube |
| Number of slats | Base: six bat poly Optional: steel tine |
| Fingers | Base: nylon Optional: steel |
| Diameter | 106.7 cm 42 in. |
| Height control | Hydraulic |
| Speed control | Hydraulic |
| Reel lift | 72 cm 28.3 in. |
| Reel fore and aft | 35.9 cm 14.1 in. |
| Fore of the cutterbar | 40.6 cm 16 in. |
| Reel resume | Base |
| Reel reverse | Base |
| Operating speeds | 6-70 rpm |
| Operating speeds (54-in. reel) | |
| Slat reel: | |
| Number of slats | |
| Diameter | |
| Height control | |
| Speed control | |
| Operating speeds | |
| Draper belts: | |
| Width | Cross belt: 101.6 cm 40 in. Center belts: 177.8 cm 70 in. |
| Belt depth | 101.2 cm 39.8 in. |
| Cleat height | Cross belt cleat height: 19.05 mm 0.75 in. |
| Operating speed | Side belts (variable): 1-3.5 m/s 3.3-11.5 fps Center belts: 211 m/min 692 fpm Low-speed center belt (fixed): 4.2 m/s 13.8 fps High-speed center belt (fixed): 5.1 m/s 16.7 fps |
| Speed control | Hydraulic from cab (side belts only) |
| Center belt reverse | Base |
| Feed drum: | |
| Diameter | 414 mm 16.3 in. |
| Feed drum fingers | Heavy-duty and round with breakaway notch and retainer Diameter: 16 mm 0.625 in. |
| Number of fingers | 21 |
| Auger finger platform | Triple chevron, retracting |
| Finger reach | 152 mm 6 in. |
| Drum/auger reverse | Base |
| Operating speed | Low speed: 200 rpm High speed: 240 rpm |
| Center cleanout door | Base |
| Header height sensing: | |
| Type | Electrohydraulic |
| Header height sensing on the ground | Base |
| Header height sensing off the ground | Optional: three sensors |
| Top auger: | |
| Type | Optional: hydraulic drive |
| Fingered augers | |
| Size | 45.7 cm 18 in. |
| Dimensions: | |
| Platform length | 10.07 m 33 ft |
| Overall operating depth | With dividers: 2.74 m 9 ft |
| Transport width, field position | 10.07 m 33 ft |
| Transport width on wheel, less dividers | |
| Transport length, hitch extended | |
| Weight: | |
| Approximate weight | 3447 kg 7600 lb |
| Additional information: | |
| Date collected | 15 June 2020 |